How to Hook Up a Water Line to a Refrigerator
To connect the refrigerator to a water line, first find a close cold-water supply line. This line could be one from the basement, the kitchen sink, or elsewhere.
- spam bots on dating sites;
- Install It.
- How to install Water Line for Samsung Refrigerator.
- free dating sites that are free.
- Related Questions.
Pull the refrigerator out from the wall, so that you have enough room to work. Then, drill a hole through the side of a cabinet or through the floor to thread the line through, depending on where your supply line is located. Next, wrap the threads on the water-line connector that is on the back of the fridge with thread-seal tape to lubricate the threads. Once the tape is on the threads, connect the water line to the threaded section. Use an adjustable wrench to tighten the nut onto the refrigerator.
Connect the line with a piercing valve clamp and close it around the pipe. Then, tighten the screws to secure the valve to the pipe.
LG Refrigerator to the Water Supply
Keep in mind that if you are going to be installing the water line onto the kitchen water supply, make sure the line sits before the shut-off valve, so that you will not shut the water off to the fridge when working on the sink. Wrap some thread-seal tape onto the threads of the piercing valve.
To install a needle valve or saddle valve, place the two clamps around the copper pipe and use a screwdriver to tighten the screws on each side to hold the valve in place. Be sure to keep the spacing equal to prevent leaking. Next, tighten down the "T" handle until it's tight and pierces the copper line.
The first part of the icemaker kit is called the solenoid valve. Locate the 2-pin solenoid connector usually found tucked or taped under the refrigerator and insert the connector over the valve solenoid terminals as far as possible.
Attach the water supply line with the provided compression fitting to the top of the solenoid valve by screwing it into place then tightening it up with a crescent wrench. Using the plastic tubing provided with the kit, screw the plastic fitting to the water outlet on the bottom of the solenoid valve. To hold the water line in place, use the provided adhesive clips to run the water line to the back of the freezer.
Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. The next step is to install the factory fill tube.
- How to Install a Refrigerator Water Line | spousalticsohin.ga;
- hvad koster dating.
- Added to Cart.
Use a flathead screwdriver to remove the plugs from the holes. It's a good idea to have a pair of needle nose pliers handy to grab the wiring harness behind the large hole in the back of the freezer.
Warranty & Support
Pull it out a few inches Image 1. Repeat this process with the water inlet plug and the mounting hole plugs located on the side of the freezer wall. Now move to the back and install the fill tube. Begin installing the fill tube by placing the provided metal insert into the end of the water supply line Image 2. Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up.
Attach the fill tube to the freezer by sliding the angled part of the tube into the inlet hole in the back of the freezer and screw it into place. With all the work done on the back side of the freezer it's time to install the icemaker unit itself. To get power to the icemaker, plug in the wiring harness on the side of the ice maker unit into the wiring harness on the back of the freezer wall. Insert the extension tube into the smaller hole on the back of the freezer wall Image 1.
Thank you for your feedback!
Screw the provided screws to the mounting holes on the side of the freezer wall Image 2. Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir. Tighten up the mounting screws to secure the unit to the freezer wall, and then add the ice bucket under the kit.
Now that the ice maker is completely installed, plug in the refrigerator. Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. Sign up for weekly project ideas and advice from experts. Run the Water Line The first step is to run the water line. Pro Tip Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking.
Drain the Water Line Now that the water line has been run to the refrigerator, it's time to do what's called the "tap-in" to the cold water line underneath the sink. Install the Valve Now that the water's off, install the new valve for the icemaker water line. Mount the Solenoid Valve The first part of the icemaker kit is called the solenoid valve.
http://chistyshifaclinic.com/media/7/libra-january-2019-horoscope-tarot.php Attach the Water Supply Line Attach the water supply line with the provided compression fitting to the top of the solenoid valve by screwing it into place then tightening it up with a crescent wrench. Install the Factory Fill Tube The next step is to install the factory fill tube. Install the Icemaker With all the work done on the back side of the freezer it's time to install the icemaker unit itself.
Mount the Unit to the Freezer Wall Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir.
How to Paint Laminate Kitchen Countertops. How to Make a Concrete Countertop 8 Steps. How to Clean Wood Cabinets. Run the Water Line Step 2: Drain the Water Line Step 3: Install the Valve Step 4: Mount the Solenoid Valve Step 5: Attach the Water Supply Line Step 6: Install the Factory Fill Tube Step 7: Install the Icemaker Step 8:
Related parts needed to hook up water to fridge
Copyright 2019 - All Right Reserved